Manual Process: Manual diagnostics process of the system through display codes, blinking codes…
Fault code reading: Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading.
Measure Values: Displays on the screen the values of the different sensors connected to the ECU. It depends on each system.
Components Actuation: They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnosis, which, for example, enable tests for engines to calibrate their state, like the cylinders balance, cylinders cut-out or compression. Depends on each system.
ECU Data: These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system.
Parameters: Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed.
Calibration: Some systems ask to calibrate some components for its correct operation. The best example are the electronic suspensions, in which there must be stored the reference values so the ECU can make function correctly.
Reset: This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not cancelled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the error codes from the memory, which is part of the diagnosis.
System Technical Data: Technical information of the system indicating the checking values, descriptions, graphics, charts…
Wiring diagram: Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier.
Vehicle Technical Data: Technical information of vehicles including all the engine technical data, tightening torques, capacities, graphics and other checking values…
Vehicle maintenance: Section in which the maintenance intervals are displayed, indicating the operations to be performed on the vehicle, and through which the reports that make the customers management easier for the workshop can be obtained.
|Antipollution||Denoxtronic 1.x, Exhaust gas treatment system|
|Antipollution||Denoxtronic 2.1, Exhaust gas treatment system|
|Auxiliary brakes||Intarder CAN, Retarder|
|Brakes||ABS D/E, Antilock braking system|
|Brakes||ABS E, Antilock braking system|
|Brakes||EBS 2, Brake central unit|
|Brakes||EBS, Electronic Braking System|
|Central computer||BC1, Body computer|
|Central computer||VCM Immobilizer Step 1, Vehicle Electronic Control Unit|
|Climate HVAC||CU, Climate control|
|Electronic module||CM, Cabin module|
|Electronic module||DDM, Driver door module|
|Electronic module||FFM, Front module|
|Electronic module||PDM, Passenger door module|
|Electronic module||RFM, Rear module|
|Engine||EDC 7 UC31, Engine Management System, Unit Injector System|
|Gearbox||Eurotronic 2, Gearbox with electronic control|
|Gearbox||Eurotronic 2, Parameter setting of the gearbox|
|Gearbox||SA 3, Allison 3000/4000 (4th Gen) - J1939, Gearbox management system|
|Gearbox||SA 3, Allison 3000/4000 (5th Gen) - J1939, Gearbox management system|
|Heater||Airtronic (Eberspächer), Air additional heater|
|Heater||Hydronic 10 (Eberspächer), Water additional heater|
|Instrument cluster||IC, Instrument cluster|
|Suspension||ECAS CAN, Electronically Controlled Air Suspension|
|Suspension||ECAS, Electronically Controlled Air Suspension|