Manual Process: Manual diagnosis process of the system through display codes, blinking codes…
Diagnostics: Allows to read the ECU failure memory by providing the user information about the error codes detected in it. This function allows the user to carry out the deleting of the errors memory; logically if the error is present, it will be detected again by the ECU and it will be displayed in the following diagnosis.
Measure Values: Displays on the screen the values of the different sensors connected to the ECU. It depends on each system.
Components Actuation: They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis,... It is the active diagnosis, which, for example for the engine, allows to carry out tests calibrating its state, like the cylinders balance, cylinders cutout or compression. Depends on each system.
ECU Data: These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system.
Parameters: Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed.
Calibration: Some systems ask to calibrate some components for its correct operation. The best example are the electronic suspensions, in which there must be stored the reference values so the ECU can make function correctly.
Reset: This point refers to the reset of the control units maintenance counters. If the maintenance operations are completed but the maintenance alarm is not cancelled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the error codes from the memory, which is part of the diagnosis.
System Technical Data: Technical information of the system indicating the checking values, descriptions, graphics, charts…
Wiring diagram: Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnosis easier.
Vehicle Technical Data: Technical information of vehicles including all the motorization technical data, tightening torques, capacities, graphics and other checking values…
Vehicle maintenance: Section in which the maintenance intervals are displayed, indicating the operations to be performed on the vehicle, and through which the reports that make the customers management easier for the workshop can be obtained.
|Antipollution||EEC, SCR AdBlue, Exhaust gas treatment system|
|Antitheft||LAS, Locking and alarm system|
|Audio system||AUS, Audio system|
|Auxiliary brakes||RET, Retarder|
|Brakes||BMS ABS, Brake management system|
|Brakes||BMS EBS, Brake management system|
|Central computer||COO, Coordinator|
|Chassis module||BWS, Bodywork management system|
|Climate HVAC||CCS, Climate Control System|
|Compressed air processing||APS, Compressed air supply|
|Data registration, telematics and FMS||AUS3 , Multimedia screen for the Telematics Infotainment System|
|Data registration, telematics and FMS||FMS, Fleet Management System|
|Data registration, telematics and FMS||ODR, Vehicle data register|
|Data registration, telematics and FMS||RTC C200, Telematic module|
|Data registration, telematics and FMS||RTI, Road Transport Information|
|Electronic module||CTS, Timer System: heater control, radio...|
|Engine||EMS HPI, High Pressure Injection|
|Engine||EMS PDE, Engine Management System, Unit Injector System|
|Gearbox||GMS, Gearbox management system|
|Heater||AHS ATA, Auxiliary heater system, air to air|
|Heater||AHS WTA, Air-water heater auxiliary system|
|Instrument cluster||ICL, Instrument cluster|
|Lighting||VIS, Visibility system|
|Lighting||VIS2, Visibility system|
|Maintenance||Service, Maintenance system|
|Powertrain||AWD, Four-wheel Drive|
|Present system detection||Systems Detection - Scania (UDS), System Scan|
|Safety||AICC, Distance sensor|
|Safety||CSS, Crash Safety System|
|Safety||DIS2, Distance sensor|
|- Calibration/Adjustment available without ADAS calibration equipment.|
|Safety||FLC, Driver assistance camera|
|- Calibration/Adjustment available with compulsory ADAS calibration equipment. Consult Jaltest Tools catalogue.|
|Safety||LDW, Lane Departure Warning Assistant|
|Suspension||SMS - ELC3, Suspension management system|
|Wheel pressure control||TPM, Tyre Pressure Monitoring System|